客服中心
4009008281
| 產品名稱 | 牌號 | 規格組距(mm) | 先款出廠價 | 備注 | |
| 基價 | 含稅價 | ||||
| 一般用途連續熱鍍鋅卷 | DX51D+Z、St01Z、St02Z | ≥0.25 | 6800 | 7956.00 | |
| ≥0.30 | 6600 | 7722.00 | |||
| ≥0.35 | 6400 | 7488.00 | |||
| ≥0.40 | 6200 | 7254.00 | |||
| ≥0.45 | 6000 | 7020.00 | |||
| ≥0.50 | 5700 | 6669.00 | |||
| ≥0.60 | 5600 | 6552.00 | |||
| ≥0.70 | 5500 | 6435.00 | |||
| ≥0.80 | 5450 | 6376.00 | |||
| ≥1.00 | 5400 | 6318.00 | |||
| ≥1.20 | 5400 | 6318.00 | |||
| ≥1.50 | 5400 | 6318.00 | |||
| 沖壓用連續熱鍍鋅卷 | DX52D+Z、St03Z | ≥0.25 | 6950 | 8131.50 | |
| ≥0.30 | 6750 | 7897.50 | |||
| ≥0.35 | 6550 | 7663.50 | |||
| ≥0.40 | 6350 | 7429.50 | |||
| ≥0.45 | 6150 | 7195.50 | |||
| ≥0.50 | 5850 | 6844.50 | |||
| ≥0.60 | 5750 | 6727.50 | |||
| ≥0.70 | 5650 | 6610.50 | |||
| ≥0.80 | 5600 | 6552.00 | |||
| ≥1.00 | 5550 | 6493.50 | |||
| ≥1.20 | 5550 | 6493.50 | |||
| ≥1.50 | 5550 | 6493.50 | |||
| 深沖壓用連續熱鍍鋅卷 | DX53D+Z、St04Z、St05Z | ≥0.25 | 7150 | 8365.50 | |
| ≥0.30 | 6950 | 8131.50 | |||
| ≥0.35 | 6750 | 7897.50 | |||
| ≥0.40 | 6550 | 7663.50 | |||
| ≥0.45 | 6350 | 7429.50 | |||
| ≥0.50 | 6050 | 7078.50 | |||
| ≥0.60 | 5950 | 6961.50 | |||
| ≥0.70 | 5850 | 6844.50 | |||
| ≥0.80 | 5800 | 6786.00 | |||
| ≥1.00 | 5750 | 6727.50 | |||
| ≥1.20 | 5750 | 6727.50 | |||
| ≥1.50 | 5750 | 6727.50 | |||
| 特深沖壓用連續熱鍍鋅卷 | DX54D+Z | ≥0.25 | 7250 | 8482.50 | |
| ≥0.30 | 7050 | 8248.50 | |||
| ≥0.35 | 6850 | 8014.50 | |||
| ≥0.40 | 6650 | 7780.50 | |||
| ≥0.45 | 6450 | 7546.50 | |||
| ≥0.50 | 6150 | 7195.50 | |||
| ≥0.60 | 6050 | 7078.50 | |||
| ≥0.70 | 5950 | 6961.50 | |||
| ≥0.80 | 5900 | 6903.00 | |||
| ≥1.00 | 5850 | 6844.50 | |||
| ≥1.20 | 5850 | 6844.50 | |||
| ≥1.50 | 5850 | 6844.50 | |||
注：1、外銷鍍鋅產品最大厚度為2.0mm，最大寬度為1120mm，表列價格均為寬度≥1000mm的卷價。
2、鋅層加減價按下表執行：
|
鍍鋅量(g/m2) |
Zn≤60 |
60＜Zn≤80 |
80＜Zn≤100 |
100＜Zn＜140 |
140≤Zn≤180 |
180＜Zn≤220 |
220＜Zn≤275 |
|
基價加減價 |
-250 |
-200 |
-150 |
-100 |
0 |
200 |
300 |
3、要求涂耐指紋膜(N)基價加價100元/噸。
4、要求環保鈍化基價加價50元/噸。
5、訂購寬度小于1000mm的鍍鋅產品，基價加價100元/噸。
(關鍵字：攀鋼 成都板材 鍍鋅 價格表)
